Optional Accessories

Maximum 25 feet. Additional hose on the air supply line. ProAir ONLY.

A lightweight and compact deck mounted power unit is installed inside of a custom steel enclosure that can be installed on either side of the platform. It is available in 1HP, 3HP, and 5HP versions depending on lift speed requirements

More typically supplied on surface mounted dock lifts. It is a hinged ramp bridging access from the floor to lift platform.

Control is keyed to only allow use to anyone with the key.

A warning buzzer or bell sounds for 2 seconds whenever the dock lift is activated to raise or lower.

A manually activated valve is provided to facilitate the lowering of the lift in the event the power supply to the lift is lost.

This is an attachment which can be placed on the portable version of the dock lift in order to move the unit. Note: The effort required to move the unit is high. The turning radius is typically large..

Checker / safety tread plate is replaced with a smooth platform deck surface with abrasive non-slip strips. Commonly used to reduce vibration during the movement of traffic across the platform.

A post with the control push button on top of it is provided on the platform of the dock lift. This option is utilized on dock lifts on which a fork lift will be driving on and being raised or lowered.

A post with the control push button on top of it on removable cord is provided on the platform of the dock lift. This option is utilized on dock lifts on which a fork lift will be driving on and being raised or lowered.

This option increases the end edge load rating of the dock lift while keeping it in place during loading and unloading. It provides steel tracks for the lifts leg rollers to run on. It eliminates wear and tear on the installation surface.

Steel angle iron with tab anchors welded along it are provided and embed into the edges of the dock lift pit. The curb angle provides a metal edge protects the pit edges from breaking away during fork lift roller overr.

A bar that is electrically interlocked, surrounds the lower perimeter of the lift's platform and electo/hydraulically arrests the downward decent of the lift when an obstruction is encountered.

This provides a lighter lifting requirement for the bridge.

This two piece hinged bridge requires two guard rails or chain posts for attachment. It facilitates easier lifting of the bridge by splitting the weight.

This hydraulic bridge assist is installed on the top platform surface of the lip. It improves safety, ergonomics and efficiency in positioning bridges or lips of this heavy nature.

This one piece hinged bridge spring assist requires one guard rail or chain post for attachment. Also available for split hined bridge.

Additional perimeter guard rails are provided to suit the application.

A hinged bridge that is hydraulically connected to automatically raise as the lift moves from the fully lowered position upward. The bridge raises to prevent the wheeled vehicle from accidentally rolling off the lift platform as it raises.

A limit switch and a mechanism  for activating the limit switch by the overhead door is provided. This interlock prevents the dock lift from being activated unless the door is in a sufficiently raised position.

This option utilizes a limit switch that stops the units upward travel at a preset travel dimension every time

For any given lift, increasing the horsepower rating of the power unit increases the lifting  travel speed of the lift.

The power supply voltages available include 115 and 220 volt single phase. 230, 460 and 600 volt 3 phase.  380 3 phase 50 hertz voltage is also available. 3 phase voltages are recommended where possible to avoid any line loss issues.

A longer version of the hinged bridge - built to specific application requirements

A wider version of the hinged bridge -built to specific application requirements.

Low height refers to the dimension from the bottom of the frame to the top of the platform when the lift table is in the fully lowered position.

The maximum amount of single axle load (in the case of rolling loads) which can be applied to the loading edge of the platform (end or side) when the lift is in any raised position.

The maximum load (evenly distributed) that the scissor lift can accomodate and lift.

The difference between the fully raised height of the lift deck and the fully lowered height of the lift .

The overall length of the lift platform surface.

The lift is installed onto a driveway or grade.

The overall width of the lift platform.

The lift is installed into recessed pit.