Electric toe sensors are most commonly used on lift tables that are installed in a preformed recessed pit. In a recessed pit installation there is the potential for introducing a shear hazard as the platform lowers into the pit. Electric toe sensors are an interlocked 4 sided bar assembly that is suspended under the lower edge of the lift table platform. The suspended perimeter bar assembly interacts with 4 limit switches, one per corner. When the down button is activated the electrical signal t... Read More
Yes you can. With the dock lift in the lowered position there is no issue. However if the dock lift is to be loaded or unloaded from the side in the raised position the dock lift capacity rating must be carefully selected to avoid platform deflection and premature wear. Dock lifts are generally loaded and unloaded from the ends. The weight moves on and off the dock lift platform travelling with the length of the scissor legs. When dock lifts are loaded and unloaded from the side the weight trave... Read More
Most lift table manufacturers recommend a maximum hydraulic hose length for remote/external power units that should not be exceeded for satisfactory performance. The issue is not raising the lift table; a pressurized hydraulic hose of almost any practical length will raise the lift table, the issue is lowering the lift table. If the lift table is lowered with weight on the platform the weight will assist in pushing the hydraulic oil back through the hydraulic hose to the reservoir. If the lift... Read More
There is no definitive answer to that question but there are reasonable expectations. A lift table that is cycled up to 8 times per hour in a single 8 hour shift and a 5 day work week should last 20+ years if properly inspected and maintained. It is very important that lift tables be designed and equipped to suit the specific requirements of the application. For example a lift table operating in a wash down application or an outdoor application should have an upgraded finish coat such as epoxy p... Read More
Although the majority of lift table applications have a single control station it is not uncommon to have multiple control stations. A typical example would be a lift table installation that services 2 different floor levels. One set of controls is located at the lower level and the secondary set of controls is located at the upper level. The lift table can now easily be called from one location to the other without the use of stairs. If the lift table can be operated from 2 locations both of th... Read More
If this option is ordered the hydraulic velocity fuse is installed in the return line of the lift table’s hydraulic circuit. As the lift table starts to lower the hydraulic oil flows out of the lift cylinder(s) and through the velocity fuse to the power unit reservoir. Depending on the model of lift table the velocity fuse is installed directly on the base of the lift cylinder or in a common manifold that monitors the returning oil flow rate from a bank of multiple lift cylinders. Velocity fus... Read More
Dock levelers and dock lifts are 2 of the most common products used at a loading dock area and are generally installed into a pre-formed concrete pit. Prior to the equipment arriving at the construction site the pits are first formed. The pit curb angle is required at that time to form the pit to the manufacturer’s specified length, width and depth. The pit curb angle is manufactured from steel angle iron and has tangs or J bolts welded to the inside of the angle for the concrete to “knit”... Read More
The overall lifting capacity is the most common and most referred to rating on a lift table. The overall rating is based on an evenly distributed load and these ratings typically range from 500 lbs to 20,000 lbs. Lift tables that are used to accommodate a rolling load such as a pallet truck or rolls of paper, coils of steel etc. have 2 additional capacity ratings; single axle end load and single axle side load ratings. The end and side load capacity ratings only apply when the lift table is in a... Read More
Although it is not very common you can use a lift truck on a dock lift if the dock lift is properly sized, rated and equipped. Some of the factors to first consider. The dock lift platform size should accommodate the overall length of the lift truck with the longest load that the lift truck will be carrying. The width of the dock lift should be sized to allow the lift truck operator to exit the lift truck and move around freely on the platform. When selecting the dock lift capacity consider a co... Read More
The majority of lift tables receive a sprayed on finish coat, this sprayed on finish coat often includes products such as enamel paint, epoxy paint or even cold spray galvanizing. None of these finishes can compare to the high performance coating of hot dip galvanizing. During the hot dip galvanizing process the components are first dipped into a tank of a cleaning acid solution, removed and then dipped into a separate tank containing the molten galvanizing solution. As opposed to any spray on f... Read More