Lift Tables & Scissor Lifts Optional Accessories

Home > Lift Tables > Lift Tables Optional Accessories

Scissor Lift Table Optional Accessories

Options for lift tables and scissor lift tables are available for all of Pentalift's extensive product line including pre-engineered lift tables as well as custom built lift tables.


The maximum load (evenly distributed) that the scissor lift can accomodate and lift.

Capacity End / Side Axle load

The maximum amount of single axle load (in the case of rolling loads) which can be applied to the loading edge of the platform (end or side) when the lift is in any raised position. This rating considers: 1) that some amount of deflection will occur during load transfer, 2) the moving and impact forces imposed by the load, 3) that this is a temporary condition during load transfer only, and 4) that the scissors lift platform is static and non- moving




End And Side Load Scissor Lift

Capacity End / Side Edge Load

The maximum amount of static load that can be applied to the edge of the platform (end or side) when the lift is in any raised position. This rating considers: 1) that some amount of deflection will occur during load transfer, 2) that this is a temporary condition during load transfer only, and 3) that the scissors lift platform is static and non moving.




End And Side Load Scissor Lift

Lowered height

Low height refers to the dimension from the bottom of the frame to the top of the platform when the lift table is in the fully lowered position.






Platform Width

The overall width of the lift platform.
Dock Lift Width

Platform Length

The overall length of the lift platform surface.
Platform Length

Vertical Travel

The difference between the fully raised height of the lift deck and the fully lowered height of the lift.
Vertical Travel Scissor Lift

Toe Sensor

Electrically interlocked perimeter bar suspended around lower outside edges of platform, stops downward travel of table when activated by coming in contact with an obstruction.
Scissor Lift Toe Senors

Hydraulic Velocity Fuse

Prevents free-fall if the hydraulic hose is severed. Note: The fuse may not lock if the lift table load is light in relation to its overall capacity.

Scissor Lift Velocity Switch

Power Unit Horse Power

For any given lift, increasing the horsepower rating of the power unit increases the lifting travel speed of the lift.

Scissor Lift Power Units

The power supply voltages available include 115 and 220 volt single phase. 230, 460 and 600 volt 3 phase.  380 3 phase 50 hertz voltage is also available. 3 phase voltages are recommended where possible to avoid any line loss issues.
Scissor Lift Table Voltages

Guarded Foot Pedal Control Station

Offers control of the raising and lowering of the lift via foot pedals.
Lift Table Fot Controls

Synchronization of multiple
lift tables

Using specialized electro hydraulic technology multiple lift tables are synchronized to raise and lower in unison.

Reinforced yellow vinyl bellows with pleats and reinforced rods help to prevent debris from entering the underside of the lift. [more...]
Nylon Bellows For Scissor Lift

Non-Standard Platform Size

Lift table platform sizes of a special length and / or width.
Non Standard Platform Size For Lift Table

Non-Standard Platform Width

Custom width platform - built to specific application requirements.
Non Standard Platform Width For Lift Table

Push Button with Coil Cord

Push button control is supplied on a 20 foot coiled cord.

Up Travel Limit Switch (Factory Installed)

This option utilizes a limit switch that stops the unit’s upward travel at a preset travel dimension every time.
Up Travel Limit Switch

Beveled Toe Guards

Tapered toe guards are provided at the sides of the lift platform. The toe guards act as a wedge to push objects away from the lowering path of the lift platform edges.
Beveled Toe Guards On Scissor Lift

Home Position Limit Switch for Rotating Platform

A limit switch that provides an electrical signal when the rotating platform is moved to the “home” position. Note: Shown with rotating top removed for clarity..
Home Positioin Limit Switch  for Rotating Platform

Spring Activated Detent Stops for Rotating Platform

Comes with spring mechanism, which automatically slips into position every 90 degrees to stop platform rotation. Rotator ONLY.

Spring Loaded Rotator Stop for Rotating Platform

A positive spring and lever detent which can be disengaged – Rotator will lock every 90 degrees.
Rotator ONLY.

Rotating Top Brake

This option stops the rotating platform at any position.
Rotator ONLY.
Rotating Platform Brake For Lift Table

Manually Operated Stop For Rotating Platform

A metal shaft locks the rotating platform in 90 degree increments.
Rotator ONLY.
Rotating Platform Brake For Lift Table

Gravity Conveyor or Chain Driven Conveyor

Available in many sizes and capacities to assist in moving product on lift table platform.
Gravity Conveyor Option For Lift  Table

High Cycle Package

High cycle bearings are provided at pivot and roller points. Utilized in applications of high cycle frequency.
High Cycle Lift Tables

Central Lubrication System

Used in conjunction with high cycle package. Provides continuous lubrication to all pivot points. Useful in applications where unit cycling is high.
Central Lubrication Option

Self-Contained Power Unit

All components which comprise the power unit are situated beneath the platform, freeing up space on the floor.
Self Contained Lift Table Power Unit

Extra Hydraulic Hose

Additional hydraulic hose to the standard of 10ft of hose.

Rotating Circular Platform

A circular shaped rotating platform. Similar in function to a “lazy Suzanne”.
Rotating Platform Option

Special Height Backstop for Tilter

For a tilter, nonstandard heights are available for the back stop.
Tilter ONLY.
Special Height Stop

Maintenance Stand for Tilter

An integral maintenance stand is provided with the lift. Tilter ONLY.

Floor Stand for Tilter

A stand that the tilter is installed onto to raise its operating position.
Tilter ONLY.
Floor Stand For Tilter Table

Restrict Tilt to 30 Degrees for Tilter

Maximum tilt is set at 30 degrees.
Tilter ONLY.

Restrict Tilt to 40 Degrees for Tilter

Maximum tilt is set at 40 degrees.
Tilter ONLY.

Load Cells

Load cells are added to facilitate weighing of product on lift.
Load Cells For Scissor Lifts

Portability Package - Caster Options

Lift table can be manually moved with load, but may not be practical if towing powered equipment. Consult factory. Both fixed and swivel casters are available in several styles. Mounting can be beneath the base frame or outboard.
Portable Lift Table Option

Ball Transfer Platform

Improves applications such as conveyor systems, directional transfer or high capacity handling.
Ball Transfer Platform Option

Remote Continuous Running Power Units

Suited to high cycling applications.

Roller Curtain

Alternative to accordion bellows, to minimize debris entry under platform. Often used in 1-2-3 sided applications..

Sure Stop Valve

Precise stopping at any position without over-run.

Access Gates

Available in many widths and can be interlocked, preventing lift table from lifting or lowering if gate is not latched.
Acccess Gate For Work Platform

Larger Air Valve for ProAir

Offers quicker cycle times for air motor power units. ProAir ONLY.
Air Valve For Pneumatic Lifts

Remote or Self Contained Air Motor Hyd Power Unit - ProAir

A supply of compressed air is used as the power source for the power unit. The electrical motor is replaced by an air motor.  Note: That the volume of air supply requirements are significant. It is important to have a source of air that can provide a significant volume of air (minimum 60 CFM). ProAir ONLY.

Regulator Filter for ProAir

Used with air motor power units to filter and regulate the pressure of the supplied air. ProAir ONLY.

Extra Pneumatic Hose for ProAir

Maximum 25 feet. Additional hose on the air supply line. ProAir ONLY.

Non-Standard Fork Width for Bin Tilter

Wider fork spacing - built to specific application requirements.
Bin Tilter ONLY.

Step-Down Floor Lock for Bin Tilter

A lock that creates friction on the floor to prevent movement of the  bin tilter. Bin Tilter ONLY.

Non-Standard Fork Length for Bin TIlter

A longer fork length - built to specific application requirements.
Bin Tilter ONLY.

Warning Device (Bell or Buzzer)

Rings for 1 to 6 seconds before up or down functions commence.

Wall Mounted Up/Down Push Button Control Station

Control station contained in a NEMA12 rated metal enclosure and mounted to an adjacent wall.

Safety Photo Eye on Approach Side Pan for No Low

Installed so that the beam protects the front edge of platform as it lowers to the floor. Stops downward movement of lift if any object obstructs the beam. No Low ONLY.

Power Unit Wall Bracket

To accommodate wall mounting of a hydraulic power unit.

Long Tandem Lifts

Two tables can be physically joined by a common platform and base.
Longer Tandum Lift Table Options

Fork Slots

Allows for unskidded loads to be placed on the top and the forks of the fork lift removed.

Anti-Skid Painted Surface

A special paint containing grit can be used in order to create a skid resistant surface.

Split and Hinge Throw-Over Plates

Use to accommodate wheeled traffic onto or off of the lift.

Protective Cylinder "BOOTS"

An accordion bellows - like sleeve which fits over cylinder rods and screws.

Fork Pocket Package

Can be either side installed or installed under frame, providing easy portability.

Stainless Steel Construction

The entire lift or components of the lift can be constructed from stainless steel.
Stainless Steel Option For Lift Table

Oversize Loads

WIde loads can be handled by increasing the width of the lift platform or base.
Oversize Loads

Solid Sheet Metal Safety Curtains

For applications where recurring equipment damage is a concern. Heavy skirting is provided down from the platform sides.
Metal Lift Tabel Curtain Option

NEMA4/4X Stainless Steel Enclosures for Power Units

Featuring all stainless steel panel construction, stainless steel hardware and piano hinge cover. Often used in exterior or wash down applications.
NEMA4X enclosure

Non-Standard Paint Color

Equipment is mechanically cleaned prior to finish and/or primer application. Product is painted with Pentalift’s standard composition alkyd enamel to the RAL specified color.
Non Standard Paint Color

Powered Portable Scissor Lift Table

Wheels and a power drive mechanism are added to the scissor lift table.
Oversize Loads

Semi-Portable Scissor Lift Table

This is an attachment which can be placed on the scissor lift in order to move the unit. The handle is removable. This option only allows the lift to be moved without a load on it.
Metal Lift Tabel Curtain Option

Pit Curb Angle

Steel angle iron with tab anchors welded along it are provided and embed into the edges of the scissor lift pit. The curb angle provides a metal edge protects the pit edges from breaking away during fork lift roller overr.

Pit Curb Angle

Controls – Removable push button on post on platform

A post with the control push button on top of it on removable cord is provided on the platform of the scissor lift. This option is utilized on lift tabes on which a fork lift will be driving on and being raised or lowered.
Removeable Push Button Controls - Dock Lift

Controls – Push button on post on platform

A post with the control push button on top of it is provided on the platform of the scissor lift. This option is utilized on lift tables on which a fork lift will be driving on and being raised or lowered.
Push Button Controls On Post
Our Primary Goal is to engineer and build the best scissor lifts and scissor lift table products to ensure the ultimate in user safety and product reliability. Please Contact a Pentalift sales representative to discuss your application requirements.